通信机房承重应不小于(A): 450-600kg/m2 400-550kg/m2 550-600kg/m2 450-650kg/m2
空调室外机必须安装在高于地面 以上的铁架上,机壳宜采用 平方毫米以上的接地线就近与地网作可靠连接 (C): 200mm,14 250mm,15 300mm,16 350mm,17
B328最大支持(B)个载扇 71 72 73 74
天线避雷针已安装到位且,能满足天线在避雷针保护范围之内,保护角:平原地区(B) ≤30° ≤45° ≤60° ≤65°
在收到UE的Up消息后,NodeB在哪个信道发送确定发射功率更新和定时调整的指令?(C) FACH RACH FPACH PCCPCH
安装GPS要满足净空(A) 120° 45° 60° 90°
关于CLKG板下列描述正确的是:( A )
CLKG板为主备配置,固定配置在1号机柜控制框的13、14两个槽位,其他机柜不配;
CLKG板为主备配置,固定配置在1号机柜控制框的9、10两个槽位,其他机柜不配; CLKG板为主备配置,可配置在任何机柜,但固定配置在9、10两个槽位; CLKG板为主备配置,可配置在任何机柜,但固定配置在13、14两个槽位;
RNC与MGW/MSCS之间的接口是: ( A ). IuCS接口;IuCS interface IuPS接口;IuPS interface
IuPS和IuPS接口;IuPS and IuPS interfaces
Iub接口;Iub interface
下列那些线缆不需要通过LPM室内防雷盒:(D ) Which cable should not go through the LPM indoor lightning protection
box? ( )
天线馈线;Antenna feeder GPS馈线;GPS feeder
TMB控制线;TMB control line
主机柜供电电源线;Power supply cable of the main cabinet
电源线标签分别贴在各线缆的两端,粘贴位置距离线鼻( B)处: Labels of power cables should be stuck to two ends of
each cable. The label is ( ) apart from the lug. 1cm 2cm 4cm
紧贴,不要距离;Very close. There is no distance
控制框的背板是 ( B ) The backplane of the control shelf is ( ) BPSN BCTC BUSN
下列哪种单板可以装配在控制框 ( A ) Which of the following boards can be assembled in the control shelf? ( )
通用控制接口板UIMC;Universal control interface board UIMC 通用媒体接口板UIMU;Universal media interface board UIMU ATM处理板APBE;ATM processing board APBE
RNC用户面处理板RUB;RNC user plane processing board RUB 下列选择中,那一项的列表不属于RNC (C ) RGUB,UIMU,RMPB OMP , VTCD,RGIM BII ,TBPA,TCCB APBE,CLK,BUSN
以下对TMB目前的安装方式描述正确的是 ( A ) Which statement about the TMB installation is correct ( )
抱杆安装和靠墙安装;Installation on a pole or mounted against a wall 抱杆安装和水平安装;Installation on a pole or horizontal installation 铁塔安装或水平安装;Installation on a tower or horizontal installation 可以任意安装在安全牢固的位置,并注意防水处理;It can be installed in any safe position. The waterproof should be
processed.
OMCR网管与RNC连接网线接入那块后插板 ( C ) RMINC RGIM RMPB RUIM
资源框的背板是 ( C ) The backplane of the resource shelf is ( ) BPSN BCTC BUSN
交换框的背板是 ( A ) The backplane of the switching shelf is ( ). BPSN BCTC BUSN
在TD系统中,GPS的作用是( D ) In the TD-SCDMA system, the function of the GPS is ( ) 提供NODE-B时钟基准;Provide the NodeB clock reference 提供NODE-B频率基准;Provide the NodeB frequency reference
提供NODE-B地理位置信息、时钟基准、频率基准;Provide NodeB geographic position information, clock reference,
frequency reference
提供NODE-B时钟基准、频率基准;Provide NodeB clock reference and frequency reference 塔顶跳线的默认配置长度为 ( D) The default length of the tower jumper is ( ) 1m 2m 3m 5m
一个DTB单板 ,最大可以提供( C )路E1接入和ATM终结功能。( ) One DTB board can provide at most ( )-channel E1
access and ATM termination functions. 8 16 32 64
一个O3站需要几个TMB ( B ) How many TMBs is needed in one O3 site? ( ) 1 2 3 4
NODE B机柜顶部2M传输电路输入的接头类型是:( D ) The connector type of 2M transmission circuit input on the top of
the cabinet in the NodeB is ( ) BNC L9 CC4Y SC
有关AAL2和AAL5的说法不正确的是(C)
在Iur接口中,控制面的AAL类型是AAL5,用户面为AAL类型是AAL2;在Iu_PS接口中,控制面的AAL类型是AAL5,用户面为AAL类型是
AAL5;在Iu_CS接口中,控制面的AAL类型是AAL5,用户面为AAL类型是AAL2;在Iub接口中,控制面的AAL类型是AAL5,用户面为AAL类
型是AAL2。In the Iur interface, the AAL type of the control plane is AAL5 and the AAL type of the user plane is
AAL2. In the Iu_PS interface, the AAL types of the control plane and user plane are both AAL5; In the Iu_CS
interface, the AAL type of the control plane is AAL5 and the AAL type of the user plane is AAL2. In the Iub
interface, the AAL type of the control plane is AAL5 and the AAL type of the user plane is AAL2. AAL2常见业务是面向连接的压缩的分组语音通讯和压缩的视频传输。AAL5常见业务是面向非连接和面向连接的数据业务。The common
services of AAL2 are connection-oriented compressed packet voice communication and compressed video transmission.
The common services of AAL5 are the connectionless-oriented and connection-oriented data services.
AAL2的服务质量是QoS4,AAL5的服务质量是QoS2。The QoS of AAL2 is QoS4 and the QoS of AAL5 is QoS2
AAL2的定时原理是:AAL2信元能够定期地向远方对等的AAL2会聚子层发送源时钟频率和网络参照时钟之间的差别指示,这样接收方就
能在很精确的范围内保持输出时钟同步,保证了语音这样的实时数据流的传送。The timing mechanism of AAL2 is: The AAL cell
can periodically transmit the difference indication between the source clock frequency and network reference clock
to the peer AAL2 convergence sublayer in the remote, so the receiver can maintain the synchronization of outputted
clock within an exact range and ensure the transmission of real-time data flow (such as the voice)
TBPA单板满负荷处理能力为8天线( D )载波数据。( ) The TBPA processing capability in the case of the full load is
eight-antenna ____ carrier data( ) 1 2 6 3
在TD系统中,按照工程规范,下面( D )说法是正确的。 In the TD-SCDMA system, which statement about the engineering
specification is correct? ( )
如果基站设备安装在机房内,在馈线进入机房时,没必要安装馈线窗。If the BTS device is installed in the equipment room,
the feeder window is not required for the feeder cable entering the equipment room. 通常将GPS天线没有必要安装在铁塔45°避雷区域内。Generally, it is not necessary to install the GPS antenna in the 45°
lightning arrester area of the iron tower.
室内接地和室外接地,可接在一起。The indoor and outdoor ground cables can be connected together
以上都不对。All of the above
用于信道估计的码是( D ) The code that is used in channel estimation is ( ) 同步码SYNC_DL;Synchronization code SYNC_DL 同步码SYNC_UL;Synchronization code SYNC_UL scrambling码;scrambling code
midamble训练序列码;midamble training sequence code
TMB 采用的供电方式为( A ) The power supply mode of the TMB is _____ ? ( ) -48V直流;-48V DC 220V交流;220V AC 110V交流;110V AC -24V交流;-24V AC
一个IMAB单板和两个DTB单板组成一组,最大可以提供( C )路E1接入和ATM终结功能。( ) One IMAB board and two DTB boards
form a group and can provide at most ( )-channel E1 access and ATM termination functions. 16 32
64 128
TD-SCDMA系统中7个常规时隙固定用于上行的时隙是(B) In the TD-SCDMA system, which of the seven normal timeslots is
fixedly used in the uplink? () TS0 TS1 TS2 TS3
( D )单板是控制框的信令交换中心,用以完成各模块间的信息交换,并提供对外连接资源框的控制以太网通道; () Which
of the following board is the signaling exchanging center of the control shelf and implements the information
exchanging between each module and provides the control Ethernet channel connecting resource shelves externally? ( )
ROMB RCB CHUB UIMC
TD-SCDMA的单载波带宽和码片速率是多少:( B ) The bandwidth and chip rate of the single carrier of TD-SCDMA are ( )
5M*2 ,3.84Mc/S 1.6M , 1.28Mc/s 1.25*2 , 1.2288Mc/S 1.6M*2 , 1.28Mc/S
2002年10月23日,中国信息产业部为我国TD-SCDMA划分的无线频率带宽为(B) The radio frequency bandwidth
allocated for TD-SCDMA by the Ministry of Information Industry in October 23, 2002 is ( ) 40M 155M 55M 200M
在RNC安装工程中,下列哪种安装不正确 ( C ) Which statement about the RNC installation is incorrect?()
走线架平直,无明显扭曲和歪斜;The cabling rack should well placed.
各种标志正确、清晰、齐全;Labels are correct, clear, and complete.
接地母线固定在走线架上,存在在空中飞线;The grounding bus is fixed on the cabling rack. There is a jumper.
布放槽道电缆时电缆不溢出槽道;The cable should not be overflowed in the case of cable distribution in the trough
TD-SCDMA系统中共有多少个长度为144码片的基本midamble码。( B ) How many basic midamble codes with the length of
144 chips are there in the TD-SCDMA system in total? ( ) 64 128 256 160
在制作馈线接头时,要始终把至少( C )的馈线拉直 When you are making the feeder connector, at least ( ) feeder should be
100mm 50mm 150mm 200mm
理论上,TD-SCDMA覆盖半径主要取决于:(C) Theoretically, the coverage radius of TD-SCDMA mainly depends on ( )
UpPTS(UL)时隙的大小;The UpPTS (UL) timeslot DwPTS(DL)时隙的大小;The DwPTS (DL) timeslot
UpPTS(UL)和DwPTS(DL)间干扰的Gp保护时隙的大小;The UpPTS (UL)-DwPTS (DL) interference Gp protection timeslot
TS0时隙的大小;The size of the TS0 timeslot
RNC室内联合接地电阻 ( A ) 小于1 欧 小于2欧 小于3 欧 小于4欧 在TD系统中,目前中兴公司使用的天线的频段是(B) In the TD-SCDMA system, the antenna band used by the ZTE is ( ) 1880—1920MHz; 2010—2025MHz; 2300—2400MHz;
以上都可;All of the above
( C ) 作为控制流汇接中心,实现交换框、资源框和控制框的控制流汇接; () Which of the following boards is the
tandem center of the control flow and implements the control flow tandem of the switching shelf, resource shelf and
control shelf? ( ) ROMB RCB CHUB UIMC
一个S333站需要配置几个TMB (C) How many TMBs are configured in one S333 site? () 2 4 6 8
多选:
下列关于TDD技术的描述正确的是:(ABCD)Which of the following statements about the TDD technology are correct? ( )
易于使用非对称频段, 无需具有特定双工间隔的成对频段;The asymmetrical frequency bands are very easy to be used in the
TDD technology and the paired frequency band with specified duplex interval is not necessary 适应用户业务需求,灵活配置时隙,优化频谱效率;The TDD technology adapts to the requirements of user services and can
flexibly configure the timeslot and optimize the spectral efficiency
上行和下行使用同个载频,故无线传播是对称的,有利于智能天线技术的实现 ;The uplink and downlink use the same carrier
frequency, so the radio transmission is symmetrical, which is beneficial for the realization of the smart antenna
technology
需笨重的射频双工器,小巧的基站,降低成本;The Node B is small and heavy radio frequency duplexer is not necessary,
so the cost is reduced
ZXTR B30机柜机頂电源盒的主要功能是( ABC )。 The main function of the power box on the top of the ZXTR B30 cabinet
is ( )
用于-48V电源的输入;Input of -48V power
对输入的电源进行滤波处理;Filtering processing for the input power
避雷器提供电源雷击保护;Arrester provides lightning protection of the power 提供-48V到220V的转换;Providing the conversion from -48V to 220V
接力切换的优点有:( ABCD ) The advantages of baton handover include ( ). 高成功率;High success ratio 低掉话率;Low call-drop ratio
高资源利用率;High resource utilization ratio 简单的切换算法;Simple handover algorithm 下列技术属于TD-SCDMA关键技术的是:( ABC ) Which of the following technologies belong to the key technologies of
TD-SCDMA? ( )
智能天线;Smart antenna 联合检测;Joint detection TDD技术;TDD technology
软切换技术;Soft handover technology 下列码长固定的码是( BCD )。 Which of the following codes have fixed code length? ( ) OVSF码;OVSF code
scrambling码;scrambling code
midamble训练序列码;midamble training sequence code 同步码SYNC_DL;Synchronization code SYNC_DL 下列属于无线层机框的单板和模块有: (ACD) Boards and modules that are installed in the wireless layer shelf
include ( )
TTRX模块;TTRX Module BCCS板;BCCS Board TBPA板;TBPA Board TFR背板;TFR Backplane
下列说法属于联合检测作用的是:(ABCD ) Which of the followings belong to the joint detection effect? ( )
降低干扰;Reduce interferences
提高系统容量;Improve the system capacity
降低功控要求;Reduce the power control requirements 削弱远近效应;Weaken the near-far effect
控制框的功能是(AB) The functions of the control shelf include ( ).
ZXTR RNC的控制核心,完成对整个系统的管理和控制It is the control core of ZXTR RNC and it manages and controls the
whole system
完成控制面信令和无线协议处理It processes the control plane signaling and radio protocol 完成控制面信令和用户面信令处理It processes the control plane signaling and user plane signaling
完成各种方式的接入处理It processes the accesses of various modes 下列描述的属于第三代移动通信系统标准的有:( )。 Which of the following standards belong to the third generation
mobile communication system? ( ABC ) CDMA2000 UMTS WCDMA TD-SCDMA CDMA IS95
对于物理层信令,下列描述正确的是( AD ) Which of the following statements about the physical layer signaling are
correct? ( )
在TD-SCDMA系统中,存在着3种类型的物理层信令:TFCI、TPC和SS ;In the TD-SCDMA system, there are three kinds of
physical layer signaling: TFCI, TPC and SS
所有的物理信道中都包含3种类型的物理层信令;All physical channels include three kinds of physical layer signaling
所有的物理信道中至少包含包含3种类型的物理层信令中的1个;All physical channels include at least one of the three
kinds of physical layer signaling
有的物理信道可以不包含物理层信令;All physical channels may not include the physical layer signaling 填空:
RGUB单板对应的后插板为 。 RMNIC
TD-SCDMA系统中共有 个长度为 码片的基本midamble码。128 144 单个TMB最大功耗 W,平均功耗 W左右。 150 100
TD-SCDMA突发的数据部分由信道码和_ 共同扩频。信道码是一个 码,扩频因子可以取 。 扰码 OVSF 1、2、4、8或16
在TD-SCMDA的帧结构中,固定地用作来发送系统广播信息时隙是 ,为避免UpPTS和DwPTS间干扰而设置的时隙是 ,训练序列码位于
TS0 保护时隙(GP) 数据域的中间位置
按阵元排列方式分,智能天线可分为 和 。 圆阵 线阵
专用传输信道DCH映射到 ,广播信道BCH映射到 ,寻呼信道PCH和前向接入信道FACH映射到 专用物理信道 (DPCH) 主公共控
制物理信道 (P-CCPCH) 辅助公共控制物理信道 (S-CCPCH) TBPA单板有 片DSP; 12
智能天线可以解决或大大改善 、 。 多址干扰 呼吸效应
单选:
关于ROMB板下列描述正确的是:(B) Which of the following statements about the ROMB board is correct? ()
ROMB板为主备配置,固定配置在1号机柜控制框的9、10两个槽位,其他机柜不配The active/standby ROMB boards are fixedly
configured in slot 9 and slot 10 of the control shelf of the No. 1 cabinet and are not configured in other cabinets
ROMB板为主备配置,固定配置在1号机柜控制框的11、12两个槽位,其他机柜不配The active/standby ROMB boards are fixedly
configured in slot 11 and slot 12 of the control shelf of the No. 1 cabinet and are not configured in other cabinets
ROMB板为主备配置,可配置在任何机柜,但固定配置在9、10两个槽位The active/standby ROMB boards can be configured in any
cabinets but are fixedly configured in slot 9 and slot 10 ROMB板为主备配置,可配置在任何机柜,但固定配置在11、12两个槽位The active/standby CLKG boards can be configured in
any cabinets but are fixedly configured in slot 11 and slot 12
用于随机接入过程的码是( B ) The code that is used in the random access process is ( ) 同步码SYNC_DL;Synchronization code SYNC_DL 同步码SYNC_UL;Synchronization code SYNC_UL scrambling码;scrambling code
midamble训练序列码;midamble training sequence code 资源框的功能,下列描述错误的是(D ) Which of the following statements about the resource shelf is incorrect? ( )
提供ZXTR RNC的对外接口,完成各种方式的接入处理It provides the external interface of ZXTR RNC and processes accesses
of various modes
完成各相关底层协议的处理It processes each related lower layer protocol
提供各种资源处理模块,完成用户面协议处理It provides various resource processing module and processes the user plane
protocol
完成控制面信令和无线协议处理It processes the control plane signaling and radio protocol
有关ATM技术特点的说明,正确的是( D ) Which of the following statements about the ATM technology features is
correct? ( )
ATM使用可变信元长度的分组交换。ATM adopts the packet switching of variable cell length ATM采用同步传输方式。ATM adopts the synchronous transfer mode ATM不兼容IP技术。ATM is incompatible with the IP technology ATM采用异步传输方式。ATM adopts the asynchronous transfer mode
用于信道估计的码是( D ) The code that is used in channel estimation is ( ) 同步码SYNC_DL;Synchronization code SYNC_DL 同步码SYNC_UL;Synchronization code SYNC_UL scrambling码;scrambling code
midamble训练序列码;midamble training sequence code
提供E1接口的单板是( D ) Which of the following boards provides the E1 interface? ( ) IMAB DTB APBE
IMAB + DTB
单框配置UIMU单板插槽位置 ( A ) 9槽(或10槽) 7槽(或8槽) 11槽(或12槽) 15槽(或16槽)
在TD系统中,在铁塔平台上安装抱杆时,抱杆与铁塔平台的最小距离是( B )。 In the TD-SCDMA system, the minimum
distance between the pole and tower platform is ( ) when a pole is installed on the tower platform 1 m 1.5 m 2 m 0.5 m
多选:
下列关于TDD技术的描述正确的是:(ABCD)。 Which of the following statements about the TDD technology are correct? ( )
易于使用非对称频段, 无需具有特定双工间隔的成对频段;The asymmetrical frequency bands are very easy to be used in the
TDD technology and the paired frequency band with specified duplex interval is not necessary
适应用户业务需求,灵活配置时隙,优化频谱效率;The TDD technology adapts to the requirements of user services and can
flexibly configure the timeslot and optimize the spectral efficiency
上行和下行使用同个载频,故无线传播是对称的,有利于智能天线技术的实现 ;The uplink and downlink use the same carrier
frequency, so the radio transmission is symmetrical, which is beneficial for the realization of the smart antenna
technology
需笨重的射频双工器,小巧的基站,降低成本;The Node B is small and heavy radio frequency duplexer is not necessary,
so the cost is reduced
三代无线通信系统的无线接口从协议结构上可以划分为(ABC )三层 According to the protocol structure, the radio
interface of the third generation mobile communication system can be divided into three layers, they are ( )
物理层;Physical layer
数据链路层;Data link layer 网络层;Network layer 媒体层;Media layer
下列叙述中正确的是( BC ) Which of the following statements are correct? ( ) 在TD-SCDMA系统中每20MS为一个无线帧;In the TD-SCDMA system, every 20ms forms a radio frame
在TD-SCDMA系统中每10MS为一个无线帧;In the TD-SCDMA system, every 10ms forms a radio frame
每个无线帧可以分成2个子帧;Each radio frame is divided into 2 subframes 每个无线帧可以分成4个子帧;Each radio frame is divided into 4 subframes
下列码长固定的码是( BCD )。 Which of the following codes have fixed code length? ( ) OVSF码;OVSF code
scrambling码;scrambling code
midamble训练序列码;midamble training sequence code 同步码SYNC_DL;Synchronization code SYNC_DL
对于物理层信令,下列描述正确的是(AD ) Which of the following statements about the physical layer signaling are
correct? ( )
在TD-SCDMA系统中,存在着3种类型的物理层信令:TFCI、TPC和SS ;In the TD-SCDMA
system, there are three kinds of
physical layer signaling: TFCI, TPC and SS
所有的物理信道中都包含3种类型的物理层信令;All physical channels include three kinds of physical layer signaling
所有的物理信道中至少包含包含3种类型的物理层信令中的1个;All physical channels include at least one of the three
kinds of physical layer signaling
有的物理信道可以不包含物理层信令;All physical channels may not include the physical layer signaling
下列说法属于联合检测作用的是:( ABCD ) Which of the followings belong to the joint detection effect? ( )
降低干扰;Reduce interferences
提高系统容量;Improve the system capacity
降低功控要求;Reduce the power control requirements 削弱远近效应;Weaken the near-far effect
填空:
板,完成无线参数的配置、控制,基带IQ数据的接收和传送,上下行信号的中频接收发送、上下变频,射频系统告警状态的管理
等功能; 无线接口板(TWIM)
IMSI由 、 、 组成。 移动国家号码(MCC) 移动网号(MNC) 移动用户识别号码(MSIN)
在TD-SCDMA系统中,存在的3种类型的物理层信令是 、 和 。 TFCI TPC SS ATM用户网络接口的ATM信元的信头包括 。 VPI、 VCI 、PTI、CLP
单选:
下列那些线缆不需要通过LPM室内防雷盒:( D ) Which cable should not go through the LPM indoor lightning protection
box? ( )
天线馈线;Antenna feeder GPS馈线;GPS feeder
TMB控制线;TMB control line
主机柜供电电源线;Power supply cable of the main cabinet
如果不接PS域,下列单板哪块单板可以不使用 ( A ) RGUB
VTCD UIMU APBE
智能天线原理采用的多址方式是( C ) The multiple access mode adopted in the smart antenna mechanism is ( )
时分多址;Time division multiple access 码分多址;Code division multiple access 空分多址;Space division multiple access 频分多址;Frequency division multiple access 下叙述中不是工程勘察的主要目的的是( C )。 Which statement does not describe the purpose of the engineering survey
( ).
为排产发货提供可靠的数据依据;Provide reliable data for production and delivery 提供工程设计的依据;Provide the standard for engineering design 进行网络规划;Perform network planning
为生产线数据配置、调试的原始依据;Provide original standard for data configuration and debugging of the production
line
在制作馈线接头时,要始终把至少( C )的馈线拉直 When you are making the feeder connector, at least ( ) feeder should be
100mm 50mm 150mm 200mm
室内接地铜排应采用()的铜排: 80mm×8mm 90mm×9mm 100mm×10mm 110mm×11mm 室内接地铜排和室外接地铜排在基站地网上的引接点,应保持一定距离,宜相距()米以上: 4 5 6 7 基站机房的交流电供电范围() 380V±10%、220V±10% 400v±10%,300V±10% 350v±10%,200v±10% 320v±10%,180v±10% 利用机房建筑物基础自然间横竖梁内的2根以上的主钢筋,组成网格不大于 的机房地网(): 2m×2m 2m×2.5m 3m×2.5m 3m×3m 机房一般要求温度为:长期 ,短期 ,当地的温度与设备的温度要求的比较决定了空调是否需要加热功能(): 10~40℃,-10~30℃ 15~30℃,0~40℃ 20~50℃,10~50℃ 25~55℃,20~60℃ RNC系统单机架最大功耗是( )。 3200w 3000w 3500w 3100w ZXTR RNC系统的外形尺寸是( )。 2000mm×800mm×800mm 2000mm×800mm×600mm 2000mm×600mm×600mm 2000mm×600mm×800mm RNC系统的交换框对应的系统背板类型是( )。 分组交换网背板(BPSN) 控制中心背板(BCTC) 通用业务网背板(BUSN) 无线层机框背板(TFR) RNC机架安装走线架要求的走线架宽度为() 300nm~600nm 300nm~400nm 200nm~607nm 200nm~600nm 接长线槽时,将一段线槽的窄端插入另一段线槽的宽端,插入深度为( ) 250mm 200mm 150mm 100mm 光纤布防需要拐弯时应该弯成圆弧,圆弧直径不小于:( ) 20mm; 40mm; 60mm; 80mm; 在彩钢板机房、活动板机房里安装室内走线架时,需要用哪种方式进行固定(): 直接固定与墙上 悬挂式 地面支撑式 以上均可 以下对机柜安装方式描述正确的是:() 底座安装方式(适用于防静电地板) 基座加底座安装方式(适用于防静电地板) 基座加底座安装方式(适用于水泥地面) 以上说法都正确 RNC机柜在安装分为防静电地板的安装以及水泥地面的安装,在安装完毕后需要检查机柜与地面的绝缘性,可以使用( )工具来检查RNC机柜是否与大地绝缘。 功率计 地阻议 万用表 水平尺 对于楼顶安装要保证智能天线周围视野开阔没有高大建筑物的阻挡,安装GPS时一般能满足净空( )要求。( )
120° 90° 150° 180° BBU机柜顶部E1线安装说明正确的是( ) E1线接线顺序按照接线端子编号由大到小取用,绑扎线扣间距为15cm E1线接线顺序按照接线端子编号由小到大取用,绑扎线扣间距为20cm E1线接线顺序按照接线端子编号由大到小取用,绑扎线扣间距为20cm E1线接线顺序按照接线端子编号由小到大取用,绑扎线扣间距为15cm RNC机架安装时候单板前各种线缆要求弯曲的角度有一定的弧度,要求大于______度弯曲。( ) 60度 90度 120度 45度 RNC机柜安装时,固定设备或底座的螺栓应全部正确安装,即依次按____ ____ ____顺序紧固并拧紧。紧固力矩应达到_____Nm。 垫圈、弹垫、螺栓 45 垫圈、弹垫、螺栓 25 弹垫、垫圈、螺栓 45 弹垫、垫圈、螺栓 25 机架(配线架、电源柜等)垂直误差超过属于严重错误。( ) 1mm 2mm 3mm 4mm 机房内不应通过的有() 给排水 煤气管道 消防管道 通风孔 机房除配备市电外还应配备以下哪些电源设备 UPS 油机发电机 蓄电池 不需配备 EI线的阻抗类型有(BD) 50欧 75欧 100欧 120 欧 目前B328机房用到的接头类型有() L9型 CC4Y型 BNC型 N型 75欧姆E1线电缆接头,常见类型有() L9 BNC CC4Y FC TD设备对机房安装净高的要求是() 2.5m 2.7M 3M 3.3M BBU-RRU的连接形式是:() E1 T1 馈线 光纤 B328设备单框配置下,电源分配插箱面板上哪些开关必须打开?( ) FAN SDH BCR1/EMC BCR2 机房除配备市电外还应配备以下哪些电源设备( )。 UPS 油机发电机 蓄电池 不需配备 关于光纤,下列说法正确的是:( ) 纤跳线和光纤尾纤弯曲半径大于等于60mm 尾纤在机架外部布放应加套管保护,套管两端延伸到机架内 套管两端应用绝缘胶带封扎,避免尾纤滑动被套管切口划伤 纤跳线和光纤尾纤在不用时应盖上防尘帽,防止划伤 地排上压接位置不够用需要一个螺栓上压接两个地线端子时,应该怎么做?( ) 采用交叉或背靠背安装方式 必须重叠时将线鼻做45°或90°弯曲处理 且应将较大铜鼻子安装于里侧,较小铜鼻子安装于外侧 且应将较小铜鼻子安装于里侧,较大铜鼻子安装于外侧 下列关于室内防雷箱的安装说法正确的是:( ) 室内防雷箱的安装高度应便于施工维护;建议防雷箱底部距地1.4m, 上端不超过2m 室内防雷箱、垂直走线槽可以安装在馈线窗和挂式空调的正下方 室外2芯电源线接入室内防雷箱时,应剥掉绝缘护套,用防雷箱自带的接地铜圈紧密压接在电源线的屏蔽层上,保证可靠接地,且裸露层不宜过多 禁止将室内防雷箱安装在蓄电池上方 对于机房UPS的要求有( ) 输入电压(V):220V±10%;输入频率(Hz):50Hz±5% 输出电压(V):220V±3%~220V±5% 输出频率(Hz):50Hz~60Hz;谐波失真:小于5% 输出波形:正弦波;工作方式:在线式;动态反应时间:小于2ms 下列问题在工程质量通用检查标准中归类于严重错误的是:( ) 机柜门保护地线未牢固连接 无单板槽位未装假面板 单板固定螺钉未拧紧或定位卡未卡到位 作业时工具未做绝缘防护处理,工具使用及摆放不正确,可能造成人身伤害、设备或电路板损坏 下列关于RNC系统设备工作环境说法错误的有( )。 温度范围长期工作需求: 0℃~ +45℃ 湿度范围长期工作需求:40%~ 65% 大气压需求70kPa~106kPa 机房接地电阻要求小于2欧姆 下列关于控制中心背板(BCTC)实现的功能需求描述中正确的是( ) 控制以太网:背板提供46×100M +1×1000的控制流以太网接入能力,其中GE端口用于UIM和CHUB板互连; 时钟接收,提取和分发:背板提供从CLKG单板接收时钟的功能,从DTB等单板提取8K时钟基准的功能,并通过电缆传送至CLKG单板,从UIM主控单板分发系统时钟至各业务槽位。 对外控制以太网汇接功能:CHUB单板对系统各资源框和一级交换框提供46个以太网接口用于系统控制流以太网汇接; 电源和地:提供-48V电源插座,提供-48VGND、GND、GNDP等各种地; 下列那几种电源线的直径符合我国的标准?( ) 16mm 25mm 32mm 240mm 工程安装时应准备安装工具,下列包括的有?( ) 内六角扳手 水平仪 切割机 指南针 当勘察新建机房时,对建筑物防雷要求描述不正确的是?( ) 在市电进入机房的线路上,不用安装电源防雷装置 在建筑物易受雷击的部位装设避雷网或避雷带 接地体宜采用建筑物本身的金属构件(如墙、柱内的钢筋)作为防雷接地的引下线,这些引下线应进行电气联通,使建筑物内的电位均衡 突出屋面的物体如烟囱、天线、水塔等,不应在其上部安装架空防雷线或避雷针 在五类线(网线)制作中使用的工具是液压钳 () 是(Yes) 否(No) 工程堪察中双面胶作用是用来粘贴设备等安装地点使用。() 是(Yes) 否(No) 设备排列方式可以并列放置也可以堆叠放置() 是(Yes) 否(No) NODEB并柜安装时两柜用地线连接,不需要分别再入地() 是(Yes) 否(No) 不论一次电源还是二次电源都可以同交换机安装在同一机房内。() 是(Yes) 否(No) Oracle安装前可以不必卸载原有Oracle文件直接安装。 ( ) 是(Yes) 否(No) 调节B328机柜的水平度的金属U型卡片应该安装在底座绝缘板的下方,禁止将该金属U 型卡安装在底座绝缘板和机柜底座之间。( ) 是(Yes) 否(No) 室外电源防雷箱与RRU的配置关系:一个室外电源防雷箱对应1个RRU。( ) 是(Yes) 否(No) GPS馈线的固定间距应不大于0.7米,一次性弯曲半径最小为20倍的线缆直径。( ) 是(Yes) 否(No) 室内馈线走线架应可靠接地,当走线架较长时,推荐每5米用多股铜线接地一次,接地线径不小于35mm2。( ) 是(Yes) 否(No) 室内、室外防雷箱的电源线的屏蔽层必须紧密压接在防雷箱的压接卡环上,做到可靠接地。 ( ) 是(Yes) 否(No) B322机架、室内防雷箱在挂墙安装时严禁安装在馈线窗和挂式空调正下方。( ) 是(Yes) 否(No) 天线附近应有有效的防雷设施,天线应安装在这些防雷设施的保护范围内,即天线接收头与避雷针或铁塔顶端的连线与竖直方向的夹角在平原地区小于45度,多雷区小于30度。( ) 是(Yes) 否(No) 同一无线通信系统的收发信机有隔离度要求,不同系统间则没有要求。( ) 是(Yes) 否(No) 产生静电的因素有:摩擦、电容的变化、电场感应。( ) 是(Yes) 否(No) 使用交流电的通讯设备和电源设备,其交流电频率允许的波动范围为 ±4%,电压波形争弦畸变率小于等于5%。( ) 是(Yes) 否(No) OT端子不得重叠安装,应采取交叉安装或者背靠背安装方式,必须重叠时应将OT端子做45度或90度弯处理,并且应将较大OT端子安装于下方,较小OT端子安装于上方。( ) 是(Yes) 否(No) 单板APBE可以配置在通用业务网背板(BUSN)上. ( ) 是(Yes) 否(No) UIMC和UIMU的功能单板相同,都是UIM_2,只是配备的子卡不同,UIMC配备的是GXS子卡,而UIMU配备的是GCS子卡. ( ) 是(Yes) 否(No)
因篇幅问题不能全部显示,请点此查看更多更全内容